如今人們對高性能的機械設備的需求與日俱增，對機器日益增長的功能及工作效率的要求，導致機器的速度更快，受力更廣，應用范圍更廣，也導致了對潤滑油的要求不斷增加。
福斯的工業用油順應了當代工業發展的潮流。這些油品具有的優良品質，遠遠超過機械廠家的規格與指標。換油周期的延長及維修費用的降低，都能助您降低成本。
福斯工業用油有相當廣的應用范圍和極高的使用壽命，該特點提供了最優的潤滑性及最低的損耗，甚至在高負荷情況下亦是如此。
液壓油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | RENOLIN B 10
RENOLIN B 15
RENOLIN B 20 | 32
46
68 | 100
100
100 | 190
210
220 | -27
-27
-24 | 通用型抗磨液壓油，用于對油品氧化、老化、抗磨及抗乳化性能有要求的場合，滿足并超過DIN HLP及ISO HM 等級。 | RENOLIN B 32 HVI
RENOLIN B 46 HVI | 32
46 | 170
170 | 175
180 | -36
-33 | 低凝抗磨液壓油，用于所有液壓系統，特別是要求高粘度指數的場合。如寒冷地區或低溫環境機器設備的液壓系統，露天作業的機器設備及工作溫度極大的液壓裝置。滿足并超過DIN HVLP及ISO HV 等級。 | RENOLIN MR 0
RENOLIN MR 1
RENOLIN MR 3
RENOLIN MR 5
RENOLIN MR 10
RENOLIN MR 15
RENOLIN MR 20
RENOLIN MR 30 | 2
5
10
22
32
46
68
100 | －－
－－
105
100
100
100
100
95 | 75
85
160
165
200
220
225
230 | -42
-33
-30
-30
-30
-30
-27
-21 | 多用途潤滑油，具有良好的抗氧化性及粘溫性能，同時還有突出的防銹、清潔、抗磨性能。Renolin MR 0,MR 1,MR 3 是機床及紡織機器主軸/錠子用油。Renolin MR 5/10/20 屬于極壓性液壓油，可在100℃的高溫下持續使用，并提供優異的防銹保護。Renolin MR 30 用于較大的齒輪箱中，亦可作為初裝及防銹油。
Renolin MR 系列產品滿足并超過DIN HLPD/CLP及ISO HMD/CKC等級。 | | HYDROTHERM 46 NP 3 | 46 | 170 | －－ | 45 | 乙二醇基的抗燃液壓油，用于接近高溫、火焰及有防火要求的液壓循環系統，主要用于冶煉、礦山、注塑成型等行業的液壓設備。滿足并超過DIN/ISO HFC 等級。 | | |
| | 導軌油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | RENEP 68K
RENEP 68K | 68
220 | 100
95 | 215
230 | -21
-16 | 精密機床水平和立式導軌潤滑油，能有效防止導軌的爬行。根據粘度的要求，又可兼作液壓油、齒輪油。滿足并超過DIN CGLP 等級。 | | |
| | 導熱油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | RENOLIN THERM 250 C
RENOLIN THERM 320 C | 14
32 | 100
100 | 175
205 | -9
-9 | 礦物油型導熱油，主要用于密閉式循環加熱系統，包括油浴爐、油熱交換器、油熱套管及油浴恒溫器等。最高使用溫度分別可達270℃及320℃。 | | |
| | 齒輪油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | RENOLIN CLP 150
RENOLIN CLP 220
RENOLIN CLP 320 | 150
220
320 | 96
96
96 | 215
220
225 | -24
-21
-15 | 通用型極壓工業齒輪油，主要用于承受高壓的軸承、連接頭及齒輪傳動系統、包括渦輪桿傳動的潤滑，并可使機器傳動系統工作穩定、噪音小。滿足并超過DIN CLP及ISO CKC 等級。 | RENOLIN CLP 150 PLUS
RENOLIN CLP 220 PLUS
RENOLIN CLP 320 PLUS | 150
220
320 | 96
96
96 | 260
260
265 | -21
-21
-21 | 極壓型工業齒輪油，其優良的減磨性能使該系列潤滑油特別適用于對抗磨、熱負荷及使用壽命有特別要求的場合，可使機器傳動系統工作平穩、噪音小。滿足并超過DIN CLP及ISO CKC 等級，并取得FLENDER認可。 | RENOLIN UNISYN CLP 150
RENOLIN UNISYN CLP 220
RENOLIN UNISYN CLP 320 | 150
220
320 | 147
148
148 | 230
232
234 | -45
-42
-39 | 全合成聚α烯烴基極壓齒輪油，與礦物油完全相溶。用于承受高壓和嚴重溫度波動的軸承及齒輪箱潤滑系統中。滿足并超過DIN CLP HC及ISO CKC 等級，并取得FLENDER認可。 | | |
| | 壓縮機油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | | RENOLIN HD 68 | 68 | 105 | 205 | -25 | 往復式空氣壓縮機油，最高使用溫度為180℃，滿足并超過DIN 51506 VCL 壓縮機油規格。 | RENOLIN SC 32
RENOLIN SC 46 | 32
46 | 100
100 | 218
225 | -21
-15 | 螺桿式空氣壓縮機油。當壓縮機工作溫度低于85℃時，建議使用RENOLIN SC 46。 | | |
| | 冷凍機油 | 產品名稱 | ISO粘度
等級 | 粘度
指數 | 開口閃點
℃ | 傾點
℃ | 主要應用 | RENOLIN PAG 46
RENOLIN PAG 46 | 55
120 | 171
190 | 220
240 | -45
-45 | 用于新型無氯制冷劑R 134a 的聚二醇基全合成冷凍機油。具有極佳的熱穩定性及減磨特性，與R 134a 相溶性良好，主要用于車輛空調壓縮機系統。 | RENOLIN TRITON SEZ 32
RENOLIN TRITON SEZ 68
RENOLIN TRITON SEZ 100 | 33.5
64.4
90.8 | 130
127
108 | 240
258
288 | -48
-45
-39 | 用于新型無氯制冷劑的合成酯基冷動機油，主要用于工業、車輛及家用空調壓縮機系統。 | |
Gearboxes designed for the transfer of power or torque can only perform effectively when excessive wear which can occur at high or fluctuating loads, particularly around the reference circle, is avoided. The life of a gearbox depends on the correct selection of the most suitable lubricating oil. The principal function of a gear oil is not just to lubricate bearings ａnd the gears themselves, i.e. to reduce friction ａnd avoid wear but also to provide protection against corrosion, to cool ａnd to seal. The RENOLIN CKC gear oils contain carefully selected base oils ａnd matched additives to protect machinery from undue wear in especially critical boundary friction conditions. RENOLIN CKC products can be classified as CKC lubricating oils according to ISO 6743-6.
The special characteristics of RENOLIN CKC series lubricants are:
- High pressure absorption ａnd excellent wear protection
- Good viscosity-temperature behaviour ａnd excellent low-temperature characteristics
- Good corrosion protection for steel ａnd nonferrous metals
- Good resistance to ageing
- Good compatibility with sealing materials
- Low foaming
- Avoidance of frictional vibration by the use of surface-active additives
- Good demulsification characteristics
- Multipurpose applications
Application:RENOLIN CKC series oils are recommended for all industrial applications where the machinery manufacturer recommends the use of a CKC type oil. Highly-stressed bearings, joints, pressure spindles, spur ａnd worm drive gears are reliably, effectively ａnd economically lubricated at temperatures of up to 120°C. The use of these oils guarantees the quiet ａnd smooth running of machinery along with optimum operational reliability. The use of these oils also allows drain intervals to be extended. Please consult our Application Engineers for suggestions on how this series of oils can be used to rationalize oil stocks.
| RENOLIN CKC | | 100 | 150 | 220 | 320 | 460 | 680 | |
| Lubricating oil type | | | | | | | | |
| acc. to ISO 6743-6 | | CKC 100 | CKC 150 | CKC 220 | CKC 320 | CKC 460 | CKC 680 | |
| acc. to DIN 51 502 | | CLP 100 | CLP 150 | CLP 220 | CLP 320 | CLP 460 | CLP 680 | |
| Characteristics | Unit | | | | | | | Test method |
| Colour | | 2 | 3 | 4 | 4.5 | 5 | 5 | ASTM D 1500 |
| Kinematic viscosity | | | | | | | | |
| at 40 °C | mm²/s | 94.4 | 145.6 | 214 | 331 | 468 | 690 | ASTM D 445 |
| at 100 °C | mm²/s | 11.1 | 14.5 | 18.5 | 24.6 | 30.8 | 36.8 | ASTM D 445 |
| Viscosity index | | 102 | 98 | 96 | 96 | 95 | 87 | ASTM D 2270 |
| Density at 15 °C | kg/l | 0.884 | 0.89 | 0.895 | 0.9 | 0.903 | 0.922 | ASTM D 1298 |
| Flash point, Cleveland open cup | °C | 220 | 225 | 230 | 230 | 240 | 245 | ASTM D 92 |
| Pour point | °C | – 27 | - 24 | - 21 | - 15 | – 12 | – 12 | ASTM D 97 |
| Neutralization number | mg KOH/g | 0.33 | 0.33 | 0.33 | 0.33 | 0.33 | 0.33 | ASTM D 974 |
| Saponification number | mg KOH/g | 1.3 | 0.84 | 0.84 | 0.84 | 0.84 | 0.84 | ASTM D 94 |
| Sulphate ash | % mass | 0.1 | 0.1 | 0.1 | 0.1 | 0.1 | 0.1 | ASTM D 874 |
| Water content | % mass | not traceable | not traceable | not traceable | not traceable | not traceable | not traceable | ASTM D 95 |
| Insolubles | % mass | not traceable | not traceable | not traceable | not traceable | not traceable | not traceable | DIN 51 592 |
| Demulsification | min | < 20 | < 20 | < 20 | < 20 | < 20 | < 20 | DIN 51 599 |
| Foaming, | | | | | | | | |
| seq. I | ml | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | ASTM D 892 seq. I-III |
| seq. II | ml | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | ASTM D 892 seq. I-III |
| seq. III | ml | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | < 10/0 | ASTM D 892 seq. I-III |
| Copper corrosion | degree of corr. | 1a-100A3 | 1a-100A3 | 1a-100A3 | 1a-100A3 | 1a-100A3 | 1a-100A3 | ASTM D 130 |
| Rust prevention | | pass B | pass B | pass B | pass B | pass B | pass B | ASTM D 665 |
| Ageing behavior, | | | | | | | | |
| viscosity increase | % | 1 | 1 | 1 | 1 | 1 | 1 | ASTM D 2893 |
| precipitation number increase | ml | < 0.05 | < 0.05 | < 0.05 | < 0.05 | < 0.05 | < 0.05 | ASTM D 2893 |
| FZG mechanical gear rig test | load stage | 12 | 12 | 12 | 12 | 12 | 12 | DIN 51 354-2 |
| Effect on SRE-NBR 1 seal material acc to DIN 53 538-1 at 100 °C +/– 1 °C after 7 days +/– 2 hours, | | | | | | | | |
| relative volume change | % | 7 | 7 | 7 | 7 | 7 | 7 | DIN 53 521 together with DIN 53 505 |
| change in Shore A hardness | Shore | - 3 | - 3 | - 3 | - 3 | - 3 | - 3 | DIN 53 521 together with DIN |
